News

How to improve the impact of high or low working e

26-10-09

1、 First, clarify the temperature boundary of the CW series The working environment temperature of CW series circular cylindrical worm reducer (CWU worm at the bottom, CWS worm at the side, CWO worm at the top) is generally -40~40 ℃; When the ambient temperature is below 0 ℃, the lubricating oil must be heated to above 0 ℃ before starting; When the ambient temperature exceeds 40 ℃, cooling measur

READ MORE
How much higher is the cooling efficiency of the g

26-10-09

Compared with air cooling solutions, the liquid cooling system for gear reducers delivers over 40% improvement in heat dissipation capacity under normal operating conditions, and its thermal conductivity can reach 3 to 5 times that of air cooling. This performance advantage becomes even more pronounced under heavy-load working conditions. The quantitative basis for this core efficiency gap is outl

READ MORE
Common Misconceptions About WPDKA250-60-11KW Worm

26-10-08

Many operators run into pitfalls when servicing the WPDKA250-60-11KW worm gear reducer. Typical mistakes cover rushed disassembly, poor lubrication control, partial component replacement without root-cause analysis, incompatible spare part selection, and disregard for assembly specifications. 1. Hasty disassembly for inspection Once abnormal operation appears, some technicians immediately tear

READ MORE
How Motor Power Impacts Load Matching of Medium Ha

26-10-08

Motor power exerts a decisive influence on load matching of ZSC gear reducers. ZSC gear reducers are commonly used in heavy machinery such as cranes and winches. Improper power matching will not only affect equipment operation but also cause direct damage to the reducer. The specific impacts are mainly reflected in the following two aspects: 1. Insufficient motor power ("small horse pulling

READ MORE
What installation details can cause unstable opera

26-09-30

1. Uneven foundation and insufficient rigidity Poor flatness of the base, failure to tighten the anchor bolts diagonally, or elastic deformation of the foundation can cause slight displacement of the box under load. The result is that the center distance and axis position of the worm gear are damaged, resulting in vibration, noise, temperature rise, and in severe cases, tooth edge contact. 2

READ MORE
What hazards can impurities invading the worm gear

26-09-30

The specific hazards can be understood as a fault chain: 1. Increased tooth surface abrasive wear When impurities such as dust, sand particles, metal filings, and oil sludge enter the meshing area, they become trapped between the worm gear tooth surface and the worm tooth surface, acting like abrasives, which damages the oil film and causes direct metal surface friction. It manifests as t

READ MORE
What performance of the BWE42-187-2.2 cycloidal ge

26-09-29

The wear of the output shaft will significantly affect the transmission accuracy, operational stability, and service life of the BWE42-187-2.2 cycloidal pinwheel reducer. If not dealt with in a timely manner, it will cause chain failures. 1、 Core performance degradation performance 1. Reduced transmission efficiency After the output shaft wears out, the clearance between it and the coupling

READ MORE
Methods for Extending the Service Life of Reducers

26-09-29

Filling equipment runs with frequent start-stop cycles, continuous operation and rigorous hygiene standards. These operating characteristics place heavy stress on reducers, the critical power transmission parts, creating tough working environments. To successfully extend reducer service life on filling machinery, five core areas should be prioritized: correct model selection, standardized installa

READ MORE
How to adjust the torque threshold of overload pro

26-09-28

1、 Adjustment steps for mechanical overload protection (friction torque limiter) 1. Confirm benchmark parameters: First, check the rated output torque of the corresponding model of BWD, and based on this, calculate the target threshold. Typically, take 1.5 to 1.8 times the rated torque. 2. Disassemble the protective end cover: Remove the dust-proof end cover on the outside of the protective

READ MORE