News

• 
  WHC120 16 2 Arc Cylindrical Worm Gear Reducer Mode

  26-09-18

  The WHC120-16-2 arc cylindrical worm gear reducer is a widely used power transmission device applied across various industrial machinery to reduce rotating speed and boost output torque. ## Model Definition - WHC: Code for arc cylindrical worm reducer with the worm positioned on the side of the worm wheel. - 120: Centre distance between worm and worm wheel, measured as 120 mm. - 16: Nomina

  READ MORE
• 
  Noise and Vibration Grade Specifications for FF57

  26-09-18

  FF57 hardened helical gear reducer is a widely used F-series parallel shaft gearbox for industrial transmission. Noise and vibration performance are core indicators to judge its operation stability and service life. This article introduces the noise and vibration level standards of the FF57 hard tooth surface gear reducer for reference in model selection, factory acceptance and daily equipment mai

  READ MORE
• 
  Step by Step Installation Guide of WSJ180 20 I Wor

  26-09-17

  ## 1. Pre-installation Inspection ### Unit Inspection Upon unpacking, inspect the reducer for shipping damage including housing cracks and distorted bearing seats. Verify model specifications match design requirements: 20:1 reduction ratio and 180mm center distance. ### Accessories Check Confirm all supplied components are complete: anchor bolts, locating pins, oil filler cap and other

  READ MORE
• 
  What Affects Eccentric Sleeve Adjustment Accuracy

  26-09-17

  For the BLEY2215-121-1.5KW cycloidal pinwheel reducer, the eccentric sleeve adjustment method is the primary means of controlling meshing clearance between the cycloidal gear and pin teeth. Given that cycloidal reducers demand tight clearance tolerances—typically maintained within 0.05–0.15 mm—the achievable adjustment accuracy is governed by two categories of factors: I. Manufacturing Quality of

  READ MORE
• 
  Advantages and Disadvantages of Hard Tooth Surface

  26-09-16

  The pros and cons of hardened tooth surface reducers and soft tooth surface reducers are outlined below: ## Hardened Tooth Surface Reducer ### Advantages (1) It features a high tooth surface hardness, typically above HRC58. The gear delivers outstanding wear resistance and can sustain greater contact stress and shock loads. Its load capacity is 2 to 3 times that of a soft tooth surface re

  READ MORE
• 
  Where the RF97 Y5.5 4P NA54 180 Reducer Fits in Sm

  26-09-16

  The RF97-Y5.5-4P-NA54-180 is a high-performance hard-tooth helical gear reducer. This RF-series horizontal-mounted reducer matches a 5.5kW 4-pole motor, features an NA54 hollow shaft with locking plate installation form, and delivers a gear reduction ratio of 180. Boasting outstanding load-bearing capacity, high transmission efficiency and stable low-vibration operation, this industrial gear reduc

  READ MORE
• 
  Adjustment guide for RX51 Y1.5 4P 2.37 M1 I reduce

  26-09-15

  Combined with field industrial experience and standard operation procedures, the detailed adjustment steps are listed below: ### 1. Pre-adjustment Preparation #### Cleaning and Inspection Fully clean bearings, shaft journals and mating mounting surfaces. Remove burrs and contaminants to guarantee no residual foreign matter. Inspect bearing conditions including wear and cracks. Replace be

  READ MORE
• 
  LD19-35-55KW Cycloidal Reducer Installation Requir

  26-09-15

  When installing the BLD19-35-55KW cycloidal pinwheel reducer, three core areas must be prioritized: stable foundation, precise transmission alignment, and compliant lubrication. This prevents operational vibration, part abrasion, and shortened service life resulting from improper installation. The detailed precautions fall into five key modules. ## 1. Pre-installation Preparation: Inspect Equip

  READ MORE
• 
  What Precautions Must Be Taken When Installing and

  26-09-14

  The successful operation of the WHC210-50-4F worm gear reducer hinges on two fundamental principles: ensuring perfect coaxiality and secure fixation during installation, and maintaining rigorous lubrication management and component inspection during operation. To guarantee optimal performance and extend the equipment's lifespan, the following specific precautions must be strictly adhered to. Inst

  READ MORE

CATEGORIES