• 
  How to deal with the scrapped BLD17-29-30KW cycloi

  25-10-22

  After the BLD17-29-30KW cycloidal pinwheel reducer is scrapped, priority should be given to following the principle of "safe disassembly → classified recycling → compliant disposal", which not only avoids environmental pollution but also maximizes the value of recycling and utilization. At the same time, attention should be paid to avoiding safety risks and environmental violations. 1. Preprocess

  READ MORE
• 
  Recommend some installation precautions for BLD19-

  25-10-22

  The installation of BLD19-35-55KW cycloidal pinwheel reducer should focus on the three core aspects of foundation stability, transmission neutrality, and lubrication compliance to avoid operational vibration, component wear, or shortened service life caused by improper installation. Specific precautions can be divided into five key modules. 1. Preparation before installation: Check the equipment

  READ MORE
• 
  How to clean the oil tank of FAF77DV132M4-NA154-7.

  25-10-21

  The cleaning of the oil tank of FAF77DV132M4-NA154-7.5KW reducer should follow the process of "thorough emptying → disassembly and cleaning → flushing and impurity removal → drying inspection". The core is to remove old oil residue, sludge, and metal debris to avoid contaminating new oil. Before operation, it is necessary to ensure that the equipment is shut down and the power is cut off, and the

  READ MORE
• 
  What are the effects of temperature exceeding 80 ℃

  25-10-21

  The impact of temperature exceeding 80 ℃ on the output shaft of WPDKS100-25-1.1KW worm gear reducer can be divided into the following aspects: 1、 Damage to core transmission components Worm gear meshing failure High temperature can cause local melting of the copper worm gear (ZCuSn10Pb1) tooth surface and bonding with the steel worm gear. If it continues for more than 30 seconds, irreversible

  READ MORE
• 
  What is the high temperature warning value set for

  25-10-20

  The setting of high temperature warning values for FAF77-2.2KW-25.47-M5 gear reducer needs to be combined with its structural characteristics and working environment. The core parameters are as follows: 1、 Temperature warning threshold setting Bearing temperature warning value Under normal operating conditions, it is recommended to set the temperature to 75 ℃ (Level 1 warning). If the tempe

  READ MORE
• 
  What are the characteristics of abnormal noises ca

  25-10-20

  The abnormal noise caused by installation deviation of WHS160-8-I worm gear reducer has the following typical characteristics, which need to be analyzed in combination with specific deviation types: 1、 Abnormal noise caused by coaxiality deviation High frequency vibration and noise When the coaxiality of the input/output shaft exceeds the tolerance (radial deviation>0.05mm or angular deviatio

  READ MORE
• 
  How to properly clean the bearing seal of FA107-Y1

  25-10-17

  The standard process for cleaning the bearing seals of FA107-Y15-4P-58.12-M1 reducer is as follows: 1. Preparation before disassembly Power off and release the residual pressure of the hydraulic system (≤ 0.5bar), mark the gear meshing phase Record the appearance status of the seal, confirm the residual amount of lubricant, and take samples for analysis Prepare specialized tools: hydraul

  READ MORE
• 
  Common faults and solutions of WPDO100-60-A worm g

  25-10-17

  The WPDO100-60-A worm gear reducer (with a center distance of 100mm and a transmission ratio of 60:1, where "A" is a specific installation configuration) is a commonly used small and medium-sized reduction equipment in industry. Due to the meshing characteristics and structural features of the worm gear, common faults are concentrated in areas such as decreased transmission efficiency, abnormal no

  READ MORE
• 
  Model parameter analysis and core performance of T

  25-10-16

  1、 Model parameter analysis The numerical part of this model corresponds to the key specifications of the gearbox, which is the basis for selection and application: TPU: In most cases, it is a series logo customized by the manufacturer, usually representing the type of "worm gear reducer". Different brands may have slight differences in heat dissipation structure and housing material, but the

  READ MORE

CATEGORIES