News

Which scenarios are suitable for RF97-Y5.5-4P-NA54

26-04-16

The RF97-Y5.5-4P-NA54-180 reducer belongs to the hard tooth helical gear reducer, and its core configuration corresponding to the model parameters is: RF series horizontal installation, compatible with 5.5kW 4-pole motor, output shaft installation form is NA54 (hollow shaft with locking plate), reduction ratio of 180, with strong load-bearing capacity, high transmission efficiency, and stable oper

READ MORE
How much gear wear does it take to replace the ZD8

26-04-14

The gear wear replacement standard for ZD80-9-11 gear reducer needs to be comprehensively judged based on equipment type, gear position, and working conditions. Usually, when the tooth thickness wear reaches 15% to 25% of the original thickness, it should be replaced. According to general industrial standards and equipment safety requirements, whether to replace gears depends not only on the am

READ MORE
How to adjust the lubrication cycle of K47-29.32-1

26-04-14

The lubrication cycle of K47-29.32-1.5KW gear reducer needs to be dynamically adjusted according to the operating conditions. Under normal circumstances, the first oil change is after 500 hours of operation, and the normal cycle is between 2000-3000 hours or annually (whichever comes first); But in harsh working conditions, the cycle needs to be significantly shortened. This model is a medium t

READ MORE
The core structure and materials of WXJ120-60 worm

26-04-13

The core structure of WXJ120-60 worm gear reducer is composed of worm gear and worm wheel. In terms of material, the worm gear is mostly made of 45 # steel or alloy steel and heat-treated, while the worm wheel is preferably made of tin bronze. The casing is commonly made of cast iron or aluminum alloy. The reducer is a single-stage cylindrical worm gear transmission structure, with the worm gea

READ MORE
After cleaning the fuel tank of the FA47-34.8-1.5K

26-04-13

After cleaning the oil tank of the FA47-34.8-1.5KW reducer, checking for any residual impurities is a key step to ensure the safe operation of the equipment. You can systematically check according to the following methods: 1. Visual inspection of internal cleanliness Use a strong flashlight or endoscope to carefully inspect the inner wall, bottom, corners, and oil interface of the fuel tank. F

READ MORE
What are the hazards of unstable operating conditi

26-04-11

The unstable operating conditions of K187-55kW gear reducer may cause equipment damage, safety accidents, and significant economic losses The unstable operation of the gearbox is a typical mechanical anomaly signal. If not dealt with in a timely manner, it will gradually evolve into a serious fault, with the following specific hazards: 1. Accelerated wear or fracture of core components [g

READ MORE
Provide some examples of selecting TPU worm gear r

26-04-11

TPU worm gear reducers have a large number of successful application cases in heavy-duty scenarios such as mining and metallurgy [gf] 200c [/gf], and their high load-bearing and impact resistance characteristics make them the preferred choice for key transmission equipment. Based on the specific application scenarios you are interested in, the following are several typical industry selection an

READ MORE
In which industries and scenarios is the WPWDK40-2

26-04-09

This model is compact in size, with moderate torque, smooth operation, and low cost. It is suitable for low-power motors (0.12-0.55KW) and focuses on light load, low speed, and small space working conditions. It is widely used in industries such as light industry, automation, agriculture and forestry, environmental protection, and medical equipment that require high equipment volume and transmissi

READ MORE
What are the steps for cleaning the interior of ZS

26-04-09

Internal cleaning steps for ZSC600-77.5-4 medium hard gear reducer: 1. Shutdown and power off, take safety precautions, clean the dust and oil stains outside the reducer, and prevent impurities from entering the interior during disassembly. 2. Open the bottom drain plug and completely drain the old lubricating oil, sludge, and impurities from the box. Preheat appropriately in winter to facil

READ MORE