• 
  How to solve the influence of environmental temper

  26-03-18

  The key to addressing the impact of environmental temperature on the compatibility of motors with ZSY315-90-1 gear reducers lies in controlling oil temperature, optimizing lubrication, matching power, and strengthening heat dissipation/preheating. According to the different working environment temperatures, targeted measures need to be taken to ensure the long-term reliable operation of the system

  READ MORE
• 
  What is the impact of ambient temperature on the c

  26-03-17

  1. If the load and speed of the equipment are changed after modification, the lubrication requirements and component bearing capacity need to be recalculated to avoid long-term overload operation of soft tooth gears and bearings, which may cause early damage; 2. Soft tooth surface gears are not resistant to impact. If they are modified for frequent start stop and forward/reverse working conditi

  READ MORE
• 
  Installation precautions for WD63-30 worm gear red

  26-03-17

  The installation quality of WD63-30 reducer directly affects the service life and operating status of the equipment. The following specifications must be strictly followed, with a focus on controlling installation accuracy and fixed reliability: 1. Base installation: The installation base should be flat and have sufficient rigidity, with a flatness error of ≤ 0.1mm/m, to avoid equipment vibrati

  READ MORE
• 
  Which type of gearbox is more suitable for use in

  26-03-16

  For high-speed equipment, planetary reducers are a better choice, followed by hard toothed helical gear reducers. These two types of reducers perform outstandingly in terms of transmission efficiency, operational stability, noise control, and structural compactness, and can better meet the comprehensive performance requirements under high-speed working conditions. 1. Planetary gearbox: preferre

  READ MORE
• 
  What is the difference in installation steps betwe

  26-03-16

  Soft tooth surface reducers and hard tooth surface reducers have similar structural shapes, but their installation requirements differ significantly due to differences in materials, heat treatment processes, and operating conditions. Overall, hard toothed reducers require higher installation accuracy, especially in terms of shaft alignment, foundation levelness, and lubrication control; The instal

  READ MORE
• 
  How to determine if the output shaft of BWD1-29-1.

  26-03-13

  The core basis for determining whether the output shaft of the BWD1-29-1.5KW cycloidal pinwheel reducer is worn is the abnormal vibration and noise during operation, as well as the radial runout of the shaft neck measured after shutdown. If the device produces periodic "clunking" sounds or significantly increases the amplitude of output vibration under load, it usually means that the journal or be

  READ MORE
• 
  What are the common modification issues for ZD60 s

  26-03-13

  The most common and high-risk issues in the modification of ZD60 soft tooth surface gear reducers are concentrated in three core dimensions: loss of transmission accuracy, lubrication and heat dissipation failure, and structural strength mismatch. 1、 Pain points and risk analysis of core modification 1. The "matching trap" of changing soft tooth surface to hard tooth surface This is the mos

  READ MORE
• 
  What are the solutions to the DCY250-80-IN gear to

  26-03-12

  The DCY250-80-IN gear reducer has a tooth surface pitting fault. The core solution is to classify the treatment according to the degree of pitting, and systematically repair and prevent it by combining material properties, lubrication status, and working condition optimization. Pitting corrosion can damage the accuracy of tooth profile, cause vibration noise, and in severe cases, can lead to tooth

  READ MORE
• 
  What is the impact of pitting corrosion fault on Z

  26-03-12

  Pitting corrosion faults can significantly reduce the load-bearing capacity and service life of ZLY250-6.3-II gearbox gears. If not dealt with in a timely manner, it will cause increased vibration, noise, and even serious consequences such as tooth surface peeling or tooth breakage. 1、 The main impact of pitting corrosion on the gears of ZLY250-6.3-II reducer 1. Decreased transmission perfor

  READ MORE

CATEGORIES