News

• 
  How to determine the model of DCY hard tooth surfa

  26-04-29

  1. Determine the type of gearbox If you need a hard tooth surface conical cylindrical gear reducer with three-stage transmission, then the type code is DCY. 2. Determine the nominal center distance (a) This is selected based on the power and torque you need to transmit. The larger the center distance, the stronger the load-bearing capacity of the gearbox. The standard center to center dis

  READ MORE
• 
  How to choose the appropriate center distance base

  26-04-27

  The selection of center distance needs to be determined based on the load size, working conditions, and the bearing capacity of the reducer. The nominal center distance range of DBY hard tooth surface conical cylindrical gear reducer is 160-560mm, and commonly used specifications include 12 types such as 160, 180, 200, 224, 250, 280, 315, 355, 400, 450, 500, 560mm, etc. The selection principle

  READ MORE
• 
  How to design and select PW series precision plane

  26-04-27

  The selection of PW series precision planetary reducers should be based on the reduction ratio, output torque, input speed, installation form, and accuracy requirements, combined with load conditions and spatial layout for system matching. 1. Determine core performance parameters Reduction ratio (i): calculated based on the speed of the driving motor and the required output speed. The PW ser

  READ MORE
• 
  What are the selection criteria for ZSY three-stag

  26-04-24

  The core of selecting ZSY three-stage cylindrical gear reducers is to ensure that the rated power of the selected model can meet the calculated power requirements under actual working conditions, and to verify the thermal power. The following are detailed selection steps and standards. 1、 Selection steps and standards 1. Clarify the basic operating parameters Before selecting, you need to

  READ MORE
• 
  ZLY Double Stage Cylindrical Gear Reducer Selectio

  26-04-24

  To select the ZLY two-stage cylindrical gear reducer, it is necessary to comprehensively consider multiple aspects such as operating parameters, mechanical strength, and thermal balance to ensure that the selected model can meet the requirements of use and be safe and reliable. 1、 Clearly define the operating parameters Before selecting, you need to prepare and provide the following detailed

  READ MORE
• 
  How to determine the fault type of shaft mounted Z

  26-04-23

  To determine the fault type of the ZJY150-16-S shaft mounted reducer, the core is to quickly locate the fault through six dimensions: listening to noise, measuring temperature, checking vibration, observing oil leakage, turning hand feel, and measuring performance, combined with its structural characteristics of shaft mounted suspension, hollow shaft, and with a check (S). The six dimensional f

  READ MORE
• 
  Common troubleshooting and solutions for WD180-47-

  26-04-23

  The common faults of WD180-47-3 worm gear reducer mainly focus on heating, oil leakage, worm gear wear, bearing damage, and abnormal lubrication, which need to be systematically investigated and graded based on the operating phenomena. Based on the structural characteristics and working conditions of this model of reducer, the following are common types of faults and their troubleshooting and s

  READ MORE
• 
  Will motor rotation error cause the XWD7-87-5.5 cy

  26-04-22

  Yes, if the motor steering error is not corrected in a timely manner, it is highly likely to cause serious damage or even scrapping of the XWD7-87-5.5 cycloidal pinwheel reducer. Although its transmission efficiency theory is not affected by steering, incorrect steering can cause a chain reaction of lubrication failure, abnormal component wear, seal leakage, and excessive temperature rise, ultimat

  READ MORE
• 
  What precautions should be taken when measuring th

  26-04-22

  The core precautions for actual torque measurement of non-standard reducers are as follows: 1、 Pre selection and working condition verification 1. Distinguish torque types and eliminate mixed testing Differentiation: rated continuous torque, peak impact torque, starting stalling torque, output static torque; Non standard reducers often do not have standard nameplate parameters, and it is

  READ MORE

CATEGORIES